M2.3 Screw & Bolt Dimensions: Diameter & Head Size

Q: What clearance hole size is needed for an M2.3 screw or bolt?

For a Close Fit, a 2.50mm drill bit is utilized. For a Normal Fit, a 2.70mm bit is used, and for a Loose Fit, a 2.90mm bit is recommended to allow the fastener body to pass through the assembly without interference.

Q: What is the difference between a bolt and a screw?

The difference is based on the intent of the fastener’s use; If the primary intent is for the fastener to pass through an unthreaded hole and be assembled with a nut, it is a Bolt. In this application, you usually hold the head and turn the nut to apply tension. But if the primary intent is for the fastener to be installed into a threaded (tapped) hole, it is a Screw. In this application, the connection is tightened by turning the head of the fastener itself.

M2.3 screw or bolt dimensions and sizes are specific fasteners often utilized in older electronic handhelds, vintage hobbyist equipment, and niche mechanical components. This size has a 2.30mm nominal major diameter and is available in M2.3 x 0.45 for the coarse series and M2.3 x 0.4 for the fine series, where 0.45 and 0.4 represent the thread pitch in millimeters. This reference chart follows respective DIN and ISO standards for each head style and DIN 13-1 (coarse series), DIN 13-21 (fine series), and ISO 68-1 standards for the thread dimensions table to ensure compatibility across metric fastening applications.

Disclaimer: Actual dimensions and tolerances may vary slightly depending on head style, manufacturer, or material — always verify with the official product datasheet before use.

Thread diagram for bolt and screw depicting the major diameter, minor diameter, pitch diameter, and thread pitch

M2.3 x 0.45 Screw & Bolt – DIN 13-1/ISO 68-1
Dimension	Size (mm)
Dimension	Min	Max
Major Diameter	2.18	2.28
Pitch Diameter	1.917	1.988
Minor Diameter	1.64	1.793
Thread Pitch	0.45
Major Diameter	2.18	2.28
Pitch Diameter	1.943	1.988
Minor Diameter	1.666	1.793
Thread Pitch	0.45

M2.3 x 0.4 Screw & Bolt – DIN 13-21/ISO 68-1
Dimension	Size (mm)
Dimension	Min	Max
Major Diameter	2.186	2.281
Pitch Diameter	1.954	2.021
Minor Diameter	1.708	1.848
Thread Pitch	0.4
Major Diameter	2.186	2.281
Pitch Diameter	1.979	2.021
Minor Diameter	1.733	1.848
Thread Pitch	0.4

Major Diameter – The largest diameter of the external thread, measured crest to crest. This defines the nominal size (e.g., M12 which is 12 mm of nominal major diameter).
Pitch Diameter – The diameter of an imaginary cylinder where the thread thickness equals the space between threads. This is the critical dimension for thread fit (Tolerance classes 2A/3A for Imperial; 6g/4g6g for Metric).
Minor Diameter – The smallest diameter of the external thread, measured root to root. This represents the core strength of the fastener and is the theoretical maximum diameter of the tap drill.
Thread Pitch – The distance from a point on one thread to the corresponding point on the next.

Hex Head – DIN 933/ISO 4017
Dimension	Size (mm)
Dimension	Min	Max
Width Across Flats	4.5	4.68
Width Across Corners	4.95	Not specified
Head Height	1.6	1.85

Metric to Inch Converter

Enter mm to convert to inches

Previous & Next Size Chart
← M2
→ M2.5

← Choose Another Size

Frequently Asked Questions

What is the tap drill size for M2.3 x 0.45 and M2.3 x 0.4 screws or bolts?

For metric fasteners, the recommended tap drill size can be calculated using this formula: Major Diameter – Thread Pitch
Therefore, for an M2.3 x 0.45 screw or bolt (coarse), the recommended tap drill is 1.85mm, while for an M2.3 x 0.4 (fine), it is 1.90mm.

What clearance hole size is needed for an M2.3 screw or bolt?

For a Close Fit, a 2.50mm drill bit is utilized. For a Normal Fit, a 2.70mm bit is used, and for a Loose Fit, a 2.90mm bit is recommended to allow the fastener body to pass through the assembly without interference.

What is the difference between a bolt and a screw?

The difference is based on the intent of the fastener’s use; If the primary intent is for the fastener to pass through an unthreaded hole and be assembled with a nut, it is a Bolt. In this application, you usually hold the head and turn the nut to apply tension. But if the primary intent is for the fastener to be installed into a threaded (tapped) hole, it is a Screw. In this application, the connection is tightened by turning the head of the fastener itself.